IEQ - Change of Equipment History

The following messages are stored in message class IEQ: Change of Equipment History.
It is part of development package IEQCM_BE in software component PM-EQM-EQ. This development package consists of objects that can be grouped under "Change of Equipment History - Backend".

Message Nr ▲	Message Text
100	* General messages ******************************************************
101	Invalid cursor position
102	Date corrected
103	Enter the date
104	Enter the notification
105	The interim status was not changed
106	The interim status is consistent
107	The interim status is not consistent
108	Select an entry
109	Processing was terminated
110	Enter the date and time between &1 &2 and &3 &4
111	Enter the event category
112	The interim status was created
113	The interim status was changed
114	The selection was corrected
115	An event was deleted
116	&1 events were deleted
117	An event was created
118	&1 events were created
119	Invalid selection
120	The data was corrected
121	The equipment is already installed
122	The equipment has already been dismantled
123	Enter the superordinate technical object
124	The SAP ECC Extension &1 is not active
125	The interim status was deleted
126	The target history is based on the template &1
127	Use transaction &1
128	Relations for measurement reading transfer are constructed in background
129	Phase "&1" is starting
130	Phase "&1" is completed
131	Phase "&1" is not required
132	The intermediate status is being processed
133	The SAP ECC Extension &1 is active
134	Function cannot be executed at this time
200	* Messages for measuring objects ****************************************
201	The object number for event &1 &2 is missing
202	There are no changes that are relevant
203	The equipment number for the event &1 &2 is missing
204	There are no changes that must be cancelled
205	The first event &1 &2 is not an installation
206	The superordinate technical object for the event &1 &2 is missing
207	Peform the new installation again
208	Event &1 &2 deleted in table &3
209	Perform the new installation
210	The old data is cancelled
211	The new data was constructed
212	Check the individual measurement document &1 for measuring point &2
213	No individual measurement documents could be determined
214	There are no changes to be created
215	Cannot determine measurement reading transfer relatnships automatically
249	BTE connection is not active
250	CRM-coupling is not supported
251	Notification processing is not supported
252	Structure gaps are not supported
253	Goods movements are not supported
254	BTE connection is active
255	CRM-coupling is supported
256	Notification processing is supported
257	Structure gaps are supported
258	Goods movements are supported
260	Asset coupling is not supported
261	Asset coupling is supported
300	* Messages on history change *******************************************
301	Equipment &1 is not available
302	Equipment &1 is not yet created for the time &2 &3
303	The event &1 &2 does not exist
304	Event &1 &2 is before the last event &3 &4
305	Equipment &1 cannot be locked
306	You have not made any changes
307	Superordinate equipment &1 is not available
308	Superordinate equipment &1 is not created for the time &2 &3
309	Eqmt &2:Error during data transfer from superordinate technical object &1
310	You have no authorization to change equipment &1
311	Error during the data transfer from eqmt &2 to subordinate equipment &1
312	Equipment &1 instantiated
313	Data was transferred from equipment &2 to the subordinate equipment &1
314	Error creating the history
315	Template &1 cannot be used
316	Event &1 &2 is not consistent
317	The desired changes to event &1 & 2 are not allowed
318	After the replacement, no further changes are allowed
319	Superordinate equipment cannot be deleted
320	Equipment &1 is already used in the hierarchy
321	The desired changes to event &1 &2 were made
322	Event &1 &2 does not contain any relevant changes for the history
323	No history is intended for the equipment &1
324	Actual history has been replaced by target history
325	Change documents were updated
326	Data was transferred to CRM-coupling
327	Data was transferred to asset coupling
328	Changes to field &1 are ignored by the system
329	Start of data transfer from equipment &2 to subordinate equipment &1
330	Only single installation is allowed at functional location &1
331	Equipment &1 is installed in different positions in the hierarchy
650	* Test messages *********************************************************
651	&1 &2 &3 &4
700	* Program errors ********************************************************
701	&1: Incorrect transfer parameter(s)
702	&1: No entry(s) in table (&2)
703	&1: Table (&2) has (&3) entry(s)
704	&1: Function code (&2) is not defined
705	&1: Memory ID (&2) is not defined
706	&1: Status (&2) is not defined
707	&1: Screen (&2) is not defined
708	&1: Answer (&2) is not defined
709	&1: Value (&2) is not defined
710	Update could not be completed successfully
711	&1: Implementation (&2) is not defined
712	Program error!
713	Contact SAP
714	Save the error log
715	Save the short dump
800	* System errors *********************************************************
801	&1: Error in adding to the database table (&2)
802	&1: Error in changing the database table (&2)
803	&1: Error in deleting from the database table (&2)
804	&1: Error in loop using the internal table (&2)
805	&1: Error in reading the internal table (&2)
806	&1: Error in adding to the internal table (&2)
807	&1: Error in changing the internal table (&2)
808	&1: Error when deleting from the internal table (&2)
809	&1: Error in executing the function module
810	&1: Error in assigning the field (&2) of component (&3)
811	&1: Error (&2) in executing the replacement
812	&1: Error (&2) when executing the function module
813	&1: Error (&2) when executing the method (&3)